| THE H & S Grinder Mixer |
 |
|
|
| ADDITIONAL OPTIONS AVAILABLE: |
*Swinging Auger Feeder
*Electronic Scales & Weight Bars (add 40# to the weight of the mixer)
*Axle Sets - Standard or Electronic Scale (Adaptable)
*13 Grinder Screen Sizes 3/32'' to 2''
*Transport Lighting Kit
*Fenders |
| Key Features: |
 |
THE FEEDING ATTACHMENTS AND UNLOADING MECHANISMS ARE ALL DRIVEN
HYDRAULICALLY - NO DRIVE BELTS, CHAINS OR GEAR CLUSTERS TO WEAR OUT. AN AVAILABLE 12'' DIAMETER BY 7' LONG HYDRAULICALLY
DRIVEN FEEDER AUGER MOVES GRAIN, EAR CORN, SHELLED CORN, OR OTHER MISCELLANEOUS GRAINS INTO THE MILL WITH EASE AND THE
HYDRAULIC CONTROL ALLOWS YOU TO KEEP THE MILL AT MAXIMUM CAPACITY. |
 |
THE 300 DEGREE SWING RADIUS OF THE UNLOADING AUGER ALLOWS REPOSITIONING OF THE DISCHARGE
TUBE FROM ONE SIDE OF THE MACHINE TO THE OTHER WITHOUT MOVING THE GRINDER-MIXER. A 14'' MIXING AUGER WITH A 30'' BASE PROVIDES
SUPERIOR MIXING UNIFORMALLY AND TWO FULL LENGTH FEED WINDOWS ALLOW THE OPERATOR TO SEE FEED LEVELS. |
 |
THE DISCHARGE AUGER HAS A VARIABLE SPEED CONTROL AND THE 10 MICRON OIL FILTER PROVIDES
A FLOW OF 10.5 GPM. |
 |
THE SELF-CONTAINED HYDRAULIC SYSTEM INCLUDES A PULLEY-DRIVEN PUMP, CYLONIC RESERVOIR
FOR MAXIMUM HYDRAULIC COOLING AND A PRESSURE RELIEF VALVE. |
 |
SIXTY-SIX THIN, FOUR WAY STEEL ALLOY REVERSIBLE HAMMERS REDUCE HORSEPOWER REQUIREMENTS,
CUTTING THE MATERIAL - NOT POUNDING IT. CUTTING ACTION OCCURS AGAINST THE THROAT PLATE WHILE A SUCTION
FAN PULLS THE GROUND FEED THROUGH THE SCREENS. THIS ALLOWS FOR A MORE UNIFORM MIX FOR RATION CONTROL. THIRTEEN
SCREENS ARE AVAILABLE WITH SIZES RANGING FROM 3/32'' TO 2'' IN DIAMETER TO GRIND THE GRAIN TO THE CONSISTENCY
THAT YOU DESIRE. |
 |
A 23'' WIDE x 18'' LONG SUPPLEMENT HOPPER WITH A SACK CUTTER IS SIDE MOUNTED 35'' ABOVE THE GROUND. |
 |
AN ECONOMICAL GRAVITY HOPPER IS AVAILABLE FOR GRINDING SHELLED CORN, OATS, BARLEY AND OTHER
SMALL GRAINS. TWO HEAVY-DUTY MAGNETS REMOVE METAL THAT MAY ACCIDENTALLY MIX WITH THE MATERIAL ENTERING THE MILL. |
 |
THE PTO DRIVEN 21'' GRINDER MILL FEATURES AN EIGHT ''A'' SECTION BANDED V-BELT FOR A POSITIVE DRIVE. |
GENERAL SPECIFICATIONS |
| Tank Capacity - Bushel |
135 |
| Tank Capacity - Cubic Ft. |
170 |
| Tank Diameter |
72'' |
| Diameter of Mixing Auger |
14'' Diameter w/30'' Base |
| Ladder |
Standard - Front Mount Over Mill |
| Tank Windows |
2 - Full Length |
| Overall Height |
10' 7'' |
| Overall Width |
7' 9'' w/o Auger Feeder |
| Overall Length |
15' 8'' |
| Ground Clearance |
11 1/2'' |
| Supplement Hopper |
23'' W x 18'' L - 35'' Above Ground |
| Feeder |
Gravity Hopper or Feed Auger |
| PTO Drive |
540 or 1000 RPM |
| H.P. Requirement |
540 RPM up to 115 HP - 1000 RPM up to 145 HP |
| Tires |
12.5L - 15 |
| Jack |
Standard |
| Weight w/Auger Feeder |
3,600# |
| AUGER FEEDER |
| Auger Feeder Length |
84'' |
| Auger Diameter |
12'' |
| Infeed Hopper |
42'' w/Fold-In-Flare - Adjustable as low as 20'' |
| Drive |
Direct Drive Independent Hydraulic Motor |
| MILL |
| Hammermill Width |
21'' |
| Cylinder Diameter |
20'' |
| Grinder Drive |
8 ''A'' Section Banded V-Belt |
| Grinder Hammers |
66-4 Way Reversible Steel Alloy |
| Grinder Screen Area |
600 Square Inches |
| Throat Magnet |
8'' x 18'' |
| Speed |
2700 RPM |
| DISCHARGE CONVEYOR |
| Unloading Auger Tube Diameter |
8'' |
| Unloading Auger Length |
12' |
| Unloading Auger Rotation |
300 Degrees |
| Unloading Auger Reach Standard |
19' @ 53 Degrees |
| Unloading Auger w/3' Extension |
Available Summer 2007 |
| Unloading Auger w/6' Extension |
Available Summer 2007 |
| DRIVE SYSTEM |
| Self-Contained |
Includes Pully-Driven Pump, Reservoir & Pressure Relief Valve |
| Pump Pressure |
2,000 PSI Maximum |
| Oil Flow |
10.5 G.P.M. |
| Hydrualic Reservoir |
Cyclonic Reservoir |
| Oil Filter |
10 Micron |
|
|
